Baumer OADM 13T6475/S35A Bedienungsanleitung Seite 6

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 5
6/8
OADM 13T6475/S35A
5.5 Besonderheiten permanent periodische Ausgabe
Die Ausgabe wird durch Senden des Reset Kommandos oder Ausschalten des
Sensors a/jointfilesconvert/1628564/bgebrochen. Nach dem Einschalten sendet der Sensor nicht mehr
periodisch.
5.6 Format der Ausgabe von „Get Konfiguration“
Ausgabe Skalierung (mm,µm..) 1 Byte
Ausgabeformat (Binär, ASCII) 1 Byte
Wartezeit für permanentperiodische Ausgabe 1 Byte
Softwareversion 6 Byte( XXYYZZ)
Hardwareversion 2 Byte (XY)
Produktionsdatum 6 Byte (TTMMJJ)
5.4 Binäres Format
Das binäre Format wird nur in der permanenten periodischen Ausgabe verwendet
um die Messdaten mit maximaler Datenrate zu übertragen. Aus diesem Grund
ist das binäre Format sehr kompakt und mit minimalem Overhead versehen.
Das Datenformat der Messwerte ist immer: Sensoreinheiten.
Im ersten Byte ist Bit 7 = 1 Markierung für Start des Datensatzes
Bit 0..Bit 6 sind Bit 7 .. 13 des Messwertes
Im zweiten Byte ist Bit 7 = 0,
Bit 0..Bit 6 sind Bit 0..6 des Messwertes
Falls die Abschwächung auch für die Ausgabe gewählt war, dann folgen 2 weitere
Bytes
Im dritten Byte ist Bit 7 = 0,
Bit 0..Bit 6 sind Bit 7..13 des Abschwächungswerts
Im vierten Byte ist Bit 7 = 0,
Bit 0..Bit 6 sind Bit 0..6 des Abschwächungswertes
Bespiel: nur Messwert
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 1 1 0 1 0 1 1 1 1
Byte 2 0 1 1 1 0 1 1 0
Resultat Messwert:
Binär 01 0111 1111 0110
Dezimal 6134
Hexadezimal 0x17F6
Bespiel: Messwert und Abschwächung
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 1 1 0 1 0 1 1 1 1
Byte 2 0 1 1 1 0 1 1 0
Byte 3 0 0 0 0 1 0 1 1
Byte 4 0 1 1 1 0 0 1 0
Resultat Messwert:
Binär 01 0111 1111 0110
Dezimal 6134
Hexadezimal 0x17F6
Resultat Abschwächung:
Binär 00 0101 1111 0010
Dezimal 1522
Hexadezimal 0x5F2
5.4 Format binaire
Le format binaire est seulement utilisé pour l’édition périodique permanente afin de
transmettre les données de mesure avec un taux de transfert des données maximal.
Pour cette raison, le format binaire est très compact. Le format des données des
valeurs de mesure est toujours: Unités du détecteur.
Pour le premier octet, on a: Bit 7 = 1 Marquage pour le démarrage du bloc de
données
Bit 0..Bit 6 sont les Bit 7 .. 13 de la valeur de mesure
Pour le deuxième octet, on a: Bit 7 = 0,
Bit 0..Bit 6 sont les Bit 0..6 de la valeur de mesure
Si l’affaiblissement a aussi été choisi pour l’édition des données, 2 octets
supplémentaires suivent:
Pour le troisième octet, on a: Bit 7 = 0,
Bit 0..Bit 6 sont les Bit 7..13 de la valeur de
l’affaiblissement
Pour le quatrième octet, on a: Bit 7 = 0,
Bit 0..Bit 6 sont les Bit 0..6 de la valeur de
l’affaiblissement
Exemple: seulement valeur de mesure
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Octet1 1 0 1 0 1 1 1 1
Octet2 0 1 1 1 0 1 1 0
Résultat valeur de mesure:
Binaire 01 0111 1111 0110
Décimale 6134
Hexadécimale 0x17F6
Exemple: valeur de mesure et affaiblissement
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Octet1 1 0 1 0 1 1 1 1
Octet2 0 1 1 1 0 1 1 0
Octet3 0 0 0 0 1 0 1 1
Octet4 0 1 1 1 0 0 1 0
Résultat valeur de mesure:
Binaire 01 0111 1111 0110
Décimale 6134
Hexadécimale 0x17F6
Résultat affaiblissement
Binaire 00 0101 1111 0010
Décimale 1522
Hexadécimale 0x5F2
5.5 Particularités pour l’édition des données périodique permanente
L’édition des données est interrompue en envoyant l’ordre de commande Reset
ou hors du sensors ou à la suite d’un déclenchement. Après un nouvel
enclenchement, le détecteur n’émet plus de façon périodique.
5.6 Format d’édition de „Get Configuration“
Edition de la mise à l’échelle (mm,µm..) 1 octet
Format de l’édition (Binaire, ASCII) 1 octet
Intervalle de temps pour édition périodique permanente 1 octet
Version logiciel 6 octets ( XXYYZZ)
Version Hardware 2 octets (XY)
Date de production 6 octets (TTMMJJ)
5.4 Binary format
The binary format is only used in the permanent periodical signal output mode in order
to transmit the measured data with the highest possible data rate. For that reason the
binary format is very compact with only minimal overhead. The data format of the
measured data is always: sensor units.
The first Byte contains Bit 7 = 1 as marker for the start of the dataset
Bit 0..Bit 6 are Bit 7 .. 13 of the measured data
The 2nd Byte contains Bit 7 = 0,
Bit 0..Bit 6 are Bit 0..6 of the measured data
Provided the attenuation has also been chosen for data output, then 2 further Bytes
are to follow
The 3rd Byte contains Bit 7 = 0,
Bit 0..Bit 6 are Bit 7..13 of the attenuation value
The 4th Byte contains Bit 7 = 0,
Bit 0..Bit 6 are Bit 0..6 of the attenuation value
Example: Only measured data:
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 1 1 0 1 0 1 1 1 1
Byte 2 0 1 1 1 0 1 1 0
Result of measured data:
Binär 01 0111 1111 0110
Dezimal 6134
Hexadezimal 0x17F6
Example: measured data and attenuation
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Byte 1 1 0 1 0 1 1 1 1
Byte 2 0 1 1 1 0 1 1 0
Byte 3 0 0 0 0 1 0 1 1
Byte 4 0 1 1 1 0 0 1 0
Result of measured data:
Binary 01 0111 1111 0110
Decimal 6134
Hexadecimal 0x17F6
Result attenuation:
Binär 00 0101 1111 0010
Dezimal 1522
Hexadezimal 0x5F2
5.5 Particular features of the permanent periodical signal output mode
The data output is interrupted by either sending the reset command or by switching
the sensor off After power-on the sensor does not send periodically anymore.
5.6 Data format of „Get configuration“
Scale of output (mm, µm..) 1 Byte
Data output format (Binary, ASCII) 1 Byte
Waiting time for permanent periodical data output 1 Byte
Software version 6 Byte (XXYYZZ)
Hardware version 2 Byte (XY)
Manufacturing date 6 Byte (TTMMJJ)
Seitenansicht 5
1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare